Weatherlink 5.9.0

**Burian&Rodan** · 21/09/2009, 20:25

Originariamente Scritto da scipio

Ciao

A me non faceva l'upload a weather underground.
Sono tornato alla precedente versione

Infatti, il problema è proprio nell'upload dei dati su Internet....

Sembra che riesca a leggere bene il "Profile 1" che contiene tutti i parametri x Internet e l'upload ma non si riesce a capire perchè ?

SB · 22/09/2009, 15:53

Quindi finora, per chi l'ha provato, l'unico incoveniente effettivo qualè?

Di miglioria mi pare di aver capito ci sia solo quella del fatto che hanno tolto il pop-up dell'upload progress? (tra l'altro per me serve per capire velocemente se l'upload avviene o meno)

Io intanto rimango sempre fedele al mio 5.7

**Scheva** · 22/09/2009, 16:18

Originariamente Scritto da SB

Quindi finora, per chi l'ha provato, l'unico incoveniente effettivo qualè?

Di miglioria mi pare di aver capito ci sia solo quella del fatto che hanno tolto il pop-up dell'upload progress? (tra l'altro per me serve per capire velocemente se l'upload avviene o meno)

Io intanto rimango sempre fedele al mio 5.7

Note: You must unplug your WeatherLink USB data logger from the USB port on your PC before you install this upgrade.
What's new in 5.9.0

The Vantage Vue weather station is supported in this software version.
Fixes USB driver dropout issue. If a dropout is detected the driver is reloaded and a remark is added to the log file.
“Expansion_Modules” folder will now be created automatically regardless of whether you have installed any expansion modules.
Wind Direction calibration can now be done via software.
Informational dialog boxes are suppressed when WeatherLink is minimized; if a screen saver has been activated or if the Bulletin, Strip charts and Plot, are running.
Added the ability to set the units that the console displays as well as what the software displays.
“Readme.wri” has been converted to “Readme.rtf” file.
Web download Password may contain special characters. These characters include: “!”, “*”, “\”, “(“, “)”, “;”, “@”, “&”, “=”, “+”, “$”,”,”, “/”, “?”, “%”, “#”, “[“, “]”.
Web download time out has been lengthened from 30 seconds to 60 seconds.
“Show indoor data only” mode is available for any Vantage console. This mode mimics the software interface for a Perception weather station and includes EMC and Air Density.
Upon entering the “Set Transceiver” screen, the software will check for model mismatch between hardware and software configuration.
Right clicking in the Bulletin now opens the Summary screen.
Now stations that are stored outside the WeatherLink directory can be renamed
Fixed the bug that causes the software, when using a dial-up modem connection, to dial the modem when you exit the software.
Fixed a bug that displayed, in the Sunrise/Sunset report, 60 minutes instead of the following hour. E.g. 5:60a will now read 6:00a
Wind Run nautical mile unit now displays as “n mi” instead of “knots”.

SB · 22/09/2009, 16:27

Originariamente Scritto da Scheva

Note: You must unplug your WeatherLink USB data logger from the USB port on your PC before you install this upgrade.
What's new in 5.9.0

The Vantage Vue weather station is supported in this software version.
Fixes USB driver dropout issue. If a dropout is detected the driver is reloaded and a remark is added to the log file.
“Expansion_Modules” folder will now be created automatically regardless of whether you have installed any expansion modules.
Wind Direction calibration can now be done via software.
Informational dialog boxes are suppressed when WeatherLink is minimized; if a screen saver has been activated or if the Bulletin, Strip charts and Plot, are running.
Added the ability to set the units that the console displays as well as what the software displays.
“Readme.wri” has been converted to “Readme.rtf” file.
Web download Password may contain special characters. These characters include: “!”, “*”, “\”, “(“, “)”, “;”, “@”, “&”, “=”, “+”, “$”,”,”, “/”, “?”, “%”, “#”, “[“, “]”.
Web download time out has been lengthened from 30 seconds to 60 seconds.
“Show indoor data only” mode is available for any Vantage console. This mode mimics the software interface for a Perception weather station and includes EMC and Air Density.
Upon entering the “Set Transceiver” screen, the software will check for model mismatch between hardware and software configuration.
Right clicking in the Bulletin now opens the Summary screen.
Now stations that are stored outside the WeatherLink directory can be renamed
Fixed the bug that causes the software, when using a dial-up modem connection, to dial the modem when you exit the software.
Fixed a bug that displayed, in the Sunrise/Sunset report, 60 minutes instead of the following hour. E.g. 5:60a will now read 6:00a
Wind Run nautical mile unit now displays as “n mi” instead of “knots”.

Azz non credevo tutte queste migliorie, Mauri che dici... installo? Io ho il DL seriale, dici che incontro problemi? Non vorrei crear casini...

**Scheva** · 22/09/2009, 16:29

Originariamente Scritto da SB

Azz non credevo tutte queste migliorie, Mauri che dici... installo? Io ho il DL seriale, dici che incontro problemi? Non vorrei crear casini...

Io l'ho installato e funziona bene , puoi provare lo scarichi e vedi come va ,per sicurezza non cancellare la versione vecchia , cosi se hai problemi ritorni a quella