Macchionis !

[C.R.]

Io conosco un metodo.

Il clone di Photoshop

E Ma Che Palle, caro Tobia...

ogni volta poi a cancellare i Macchioni da OGNI Foto!

Con la Fuji, ho resistito 3 gg... Poi, ho Tentato l'Impossibile...m'ha detto Bene!

Cl.

[Gdr]

... ogni volta poi a cancellare i Macchioni da OGNI Foto!

Considerato che ho comprato la mia HP da FNAC e che credo proprio la strada della riparazione non sia percorribile, vorrei iniziare a far mente locale sull'eventualità di dotarmi di una macchinetta nuova, hai qualche suggerimento relativamente ad un modello che sia paragonabile per prezzo e prestazioni alla mia HP 945 ? Nel frattempo guardo in rete per vedere se riesco a smontarla e a dare la soffiata di cui sopra nel posto giusto, senza ricorrere alle fessure.

[Gdr]

Nel frattempo guardo in rete per vedere se riesco a smontarla

Trovato:

dismantling the hp945

disclaimer: do not make me responsible for any damage at your camera. do not try to disassemble anything, without correct fitting tools. make notations of each screw, where it taken out, they look very similar, but are different. be carefull when handling the flash unit, high voltage is stored there, even when batterys are taken out!

do not make any actions, when you are not familiar with handling (specially opening and closing) ffc (flat-foil-cables), electronic connectors on pcb´s (printed circuit board) and a soldering iron.

dismout neckstrap and lens cover cord, strip of the rubber ring from the objective, by pushing a small screwdriver under the rubber, then the chromering, it is just clicked on. remove the rubber cap from the evf. don´t try to screw it out!

remove all black screws from the housing, one is located under the battery container door.

carefully pull the back housing backwards. now the battery container door is removeable. unplug the connector, located on the upper side of the lcd screen, red and black wire, it is the red led self-timer connection.

turn the scene switch to position "AUTO", otherwise you damage this rotation switch, when you take apart the front housing.

put the cam with the lens downwards on the table and push the housing downwards, but gently help the housing to pass the step of the evf, it clamps there a little bit.

remove 4 screws of the push button print, disconnect the screen power cable, white-grey, located and connected under the pcb.

remove the screws of the lcd sreen, carefully open the ffc connector and unplug it.

remove the tape which is fixing the red and black wire on the pcb. open the 3 ffc holders, located on top, the left one is the ccd sensor, the middle one is the objective driving, the right one is the program (scene) switch.

remove all screws, the pcb is fixed with, under the pcb you see a tape, which is fixed on the battery container, it fixes a copper cooling foil, you can`t take the pcb apart, without loosen this tape!

remove 2 screws fixing the flash unit on the front side, pull it forwards, to unplug, do not touch or pull the small flash transformer, with the white cable, it`s very delicate! also take care of the very small 10 pin connector, which connects flash unit to the main pcb. pull out the connection part, maybe it remains on the main pcb connector, this part has 10 pins on each side.

now try carefully to dismount the main pcb, by lifting it from the right side, it is not easy, because of the external connectors on the left side.

3 screws now holding the tube cover and 3 more fixing the objective, two of them are located under the middle ffc, it is fixed on the chassis with double adheshive.

the sensor is fixed on the objective with 3 black screws, remove that only in a dust free area. do not clean the sensor with any liquids, exept clear water!!!

disassembling the objective is an other difficoult story!

greetings diddel